Inside square hole

Glide plug

IQ-IFRF

With felt. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Not suitable for holes in sheet metal etc. NOTE: Less suitable for concrete and tiled floor.

Glide plug

IQ-IFRS

With thick, tilted glide surface. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc. The C measurement is given in degrees.

Glide plug

IQ-IFRVG

Suitable for horizontal tube. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc.

Glide plug

IQ-LGP23

Flexible glide part attached with steel pin. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc.

Glide plug

IQ-LGG23

Flexible glide part, with friction surface, attached with steel pin. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc.

Glide plug

IQ-LGF23

Adjustable felted glide part, attached with steel pin. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc. Less suitable for concrete and tiled floor.

Glide plug

IQ-LGM23

Flexible plated glide part attached with steel pin. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc.

Glide plug

IQ-IFR1

With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc.

End plug

IQ-IFRREGAL

Open side for shelf hooks. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc.

End plug

IQ-IFRVS

Pyramid shaped surface. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc.

End plug

IQ-IFRK

Plated surface. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc.

Chrome-plated end plug

IQ-IFRK2

Suitable for tubes and deeper holes where sharp edges and shape variations may occur.

End plug

IQ-001

Adjustable glide

SFIQ-SFIPF001

Adjustable glide

SFIQ-SFIPF014

Note: Maximum D1 measurment is with foot screwed-in to half the length of the insert.

Adjustable glide

SFIQ-SFIPF006

Note: Maximum D1 measurment is with foot screwed-in to half the length of the insert. For higher friction add 4 off GS74.5N per foot.

Adjustable glide

SFIQ-002

Note: D3=Max

Adjustable glide

SFIQ-SFIPF011

Note: Maximum D1 measurment is with foot screwed-in to the sheet metal.

Plug with threaded hole

IQTH-004

Expanding upon tightening. Intended for tightening fastening.

Plug with threaded hole

IQTH-IP

Plastic threaded plug. Suitable for light loads on qutie stationery products. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc.

Plug with threaded hole

IQTH-IPIM

Steel threaded plug. Suitable for heavier loads on quite stationery products. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc.

Plug with threaded hole

IQTH-002

Expanding upon tightening. Intended for tightening fastening.

Plug with threaded hole

IQTH-IPM

Long steel threaded plug. Suitable for quite heavy loads on mobile products. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc.

Plug with threaded hole

IQTH-IPP

Long plastic threaded plug. Suitable for light loads on mobile products. With flanges. Suitable for tubes and deeper holes where sharp edges and shape variations may occur. Note: Not suitable for holes in sheet metal etc.